AC Repair in East Bernard, TX: How to Fix 3 Frequent Troubles

There can be a couple of explanations why your AC unit won’t work: an overloaded circuit breaker, wrong thermostat settings, a shut off switch or a full condensate drain pan.

Your system won’t start when you have a blown breaker.

To check if one has blown, go to your residence’s main electrical panel. You can find this gray box on the wall in the basement, garage or closet.

• Make sure your hands and feet are dry before you work on the panel or breakers.
• Locate the breaker identified “AC” and confirm it’s in the “on” spot. If it’s triggered the lever will be in the middle or “off” spot.
• Quickly shift the switch back to the “on” position. If it instantly trips again, don’t reset it and contact us at 979-335-4262. A breaker that keeps tripping may signal your home has an electrical issue.

If your thermostat isn’t giving a sign to your air conditioner to start, it won’t activate.

The most important point is checking it’s on “cool” and not “heat.” Otherwise your air conditioner will probably not switch on. Or you could get. hot air coming from vents since the furnace is going instead.

If you rely on a digital thermostat:

• Swap out the batteries if the monitor is empty. If the screen is presenting jumbled characters, replace the thermostat.
• Make sure the proper setting is displaying. If you can’t alter it, reverse it by lowering the temperature and pushing the “hold” button. This will cause your AC to run if the configuration is wrong.
• Try setting the thermostat 5 degrees colder than the house’s temperature. Your AC won’t start if the thermostat is identical to the space’s temperature.

Once your thermostat is adjusted accurately, you should receive chilled air quickly.

If you have a smart thermostat, including ones manufactured by Nest, Ecobee, Lux, Honeywell or Bosch, look at the manufacturer’s website for help. If it still won’t work, call us at 979-335-4262 for assistance.

Your cooling equipment usually has a power-cutting switch near its condenser. This device is typically in a metal box hung on your home. If your air conditioner has recently been fixed, the switch may have accidentally been left in the “off” location.

Condensate drain pans keep the extra water your air conditioner takes out of the air. This pan can be found either below or within your furnace or air handler.

When there’s an obstruction or clogged drain, water can become concentrated and initiate a safety feature to switch off your equipment.

If your pan has a PVC pipe or drain, you can get rid of the additional condensation with a custom pan-cleaning capsule. You can buy these tabs at a home improvement or hardware shop.

If your pan involves a pump, locate the float switch. If the switch is “up” and there’s water in the pan, you may need to get a new pump. Contact us at 979-335-4262 for assistance.

If your AC is on but not cooling, its airflow might be clogged. Or it may not have enough refrigerant.

Your equipment’s airflow can be limited by a plugged air filter or dusty condenser.

A filthy filter can create numerous issues, like:

• Lower comfort
• Frosted refrigerant lines or evaporator coil
• Uneven cooling
• Bigger electricity costs
• Making your system wear out faster

We propose installing new flat filters every four weeks, and pleated filters every three months.

If you aren’t sure when you last replaced yours, switch off your equipment completely and take out the filter. You can locate the filter in your furnace or air pump’s blower compartment. It may also be found in an attached filter box or wall-mounted return air grille.

Angle the filter up to the sunshine. If you can’t see any light you should replace it.

Weeds, grass and bushes can obstruct your condensing system. This can reduce its airflow, lower its energy efficiency and change your comfort. Here’s a method you can follow to get your unit running smoothly again.

1. Turn off the electrical current totally at the breaker or outside lever.
2. Clear yard rubbish around the equipment. Once you’ve removed bigger refuse within a two-foot space, you can use a fine-bristled brush or vacuum to gingerly remove dust from the condenser fins. Kinked fins can also hurt performance, so you can attempt to straighten them with a blunt knife.
3. Use a hose nozzle to slowly remove gunk off the fins from inside the equipment. Make sure to avoid getting moisture on the fan motor.
4. Put the top back on and turn on the power.

When air conditioning units don’t have enough refrigerant, they’ll have difficulty removing heat and humidity from your residence.

Here are a couple of indications that your system is leaking refrigerant:

1. It takes too long to lower the temperature in your home and you’re regularly lowering the thermostat.
2. Air conditioning moving through the ducts isn’t as chilly as it should be.
3. You’re hearing hissing or gurgling sounds when cooling is on.
4. Your evaporator coil is iced over on account of having an issue handling warmth.

Think your unit is losing refrigerant? You need a authorized heating and cooling service professional to take care of the leak and restore the correct measurement of refrigerant in your system. Get in touch with us at 979-335-4262 for help.

When it feels like you’re not having ample amounts of cold air, there’s likely a blockage or disconnection somewhere in your cooling system.

• The beginning step is examining your air filter. Buy a new one if it’s dirty.
• Then make sure the ductwork is clear across your home.
• If you’re still not getting sufficient chilly air, you should have your ductwork inspected by a expert like E.B. Air. Your ducts could need to be serviced or rejoined in difficult spots like your attic, basement or crawl space.